Filter

SEACHEM Reef Buffer | 250g

Name: SEACHEM Reef Buffer | 250g
SKU: SCM-RBF-250
Availability: InStock
ISBN: TRUE

₹1,150.00

Reef Buffer:

Raises pH to 8.3
Raises pH and carbonate alkalinity together
pK (8.6) allows for greater pH stability in a reef system where the bioload is significantly more than in a? fish only system

SKU: SCM-RBF-250 Category: Sock Holder Tags: ph, reef, reef buffer, seachem

Description

SEACHEM Reef Buffer

When used as directed SEACHEM Reef Buffer will raise the pH of your reef system to 8.3 without fear of accidentally overshooting the pH to a dangerous level. Whereas competing products simply use sodium bicarbonate, SEACHEM Reef Buffer is made with a blend of carbonate and bicarbonate salts. This blend of salts results in SEACHEM Reef Buffer yielding a pK of roughly 8.6 in saltwater.

The pK of a buffering agent is equivalent to the pH around which that buffer most strongly buffers. One would presume, then, that the pK of a saltwater buffer should be 8.3; however, the multitude of organic acids produced by the inhabitants of a reef system forces pH downward to a much greater degree than in a non-reef, marine system. A buffer with a pK of 8.3 would end up yielding a pH more in the range of 8.0-8.2. SEACHEM Reef Buffer’s higher pK (8.6) allows for greater pH stability in a reef system where the bioload is significantly more than in a fish only system. Competing products are not designed specifically for the reef environment, so their pK is too low (in most cases, pK 8.3). At this pK, the proper pH can never be reached in saltwater.

SEACHEM Reef Buffer will also raise carbonate alkalinity; however, when pH is not an issue, Reef Builder or Reef Carbonate should be your first choice for a carbonate alkalinity supplement.

Additional Information

Directions

Check pH and alkalinity before use (use MultiTest Marine pH & Alkalinity to test ph nd alkalinity levels). Use 5 g (1 level teaspoon) for every 150 L (40 US gallons) to raise pH by about 0.1 pH units (this will also raise alkalinity by about 0.5 meq/L). For precise dosing, use the Seachem Digital Spoon Scale. Dissolve in at least 250 mL (one cup) of freshwater, then add to the tank. The pH of natural sea water is 8.25?8.30. In a well established reef system pH adjustment may be necessary biweekly to semiweekly. Dosing requirements will vary, but do not exceed the recommended dose without checking your pH and alkalinity (alkalinity should not exceed 6 meq/L).

If an alkalinity of 6 meq/L has been reached and a pH of at least 8.20 has not been attained or substantial cloudiness that does not clear within 15 minutes is encountered, then the system is not ionically balanced. To restore ionic balance perform a water change or adjust the magnesium and calcium levels to approximately 3:1 Mg:Ca.

DO NOT OVERDOSE: Excess alkalinity may enhance the loss of calcium, magnesium, and strontium. Do not directly mix with any calcium, magnesium, or strontium supplement. Best if calcium & carbonate additives are added on alternate days or at least 30 minutes apart.

Dosage

Considerations

Use MultiTest Marine pH & Alkalinity to test alkalinity levels.

Reef alkalinity should ideally be maintained at 3-6 meq/L (8-17 dKH). Reef Buffer? will raise carbonate alkalinity; however, it is intended primarily for use as a buffer in a reef system where the maintenance of a pH of 8.3 is often difficult. When pH is not an issue, try Reef Builder? or Reef Carbonate?

DO NOT OVERDOSE

Excess alkalinity may enhance the loss of calcium, magnesium, and strontium. Do not directly mix with any calcium, magnesium, or strontium supplement. Best if calcium & carbonate additives are added on alternate days or at least 30 minutes apart.

Additional information

Brand	Seachem
Aquarium Type	Reef
Weight	250 GMS

FAQs

What is the difference between Marine Buffer and Reef Buffer?

A: In short, the answer is pK. Marine Buffer is intended for a fish-only marine system and has a pK of 8.3, whereas Reef Buffer is designed specifically for a reef system and has a pK of 8.6. Because of its higher pK, Reef Buffer is more successful at overcoming the multitude of organic acids produced by reef inhabitants that tend to force pH downward in a typical reef aquarium.

What is the difference between Reef Builder and Reef Buffer?

A: While both products affect pH and alkalinity, Reef Buffer's primary function is affecting pH, while Reef Builder's primary function is affecting alkalinity. Use Reef Builder to raise carbonate alkalinity without affecting pH. Use Reef Buffer to raise carbonate alkalinity and pH.